[crfsonly]

Here's the much anticipated modification list. This will be an incredible 450x!

Yet to be determined are the following. Please clarify your suggestions for the final list on these items:

1. Which Exhaust? Yosh Carbon, E2, Stock, Others
2. Which CAM? Stoc, Stage 1, Stage 2, Other?
3. Fluidyne Radiators? Stay with stock or go with Fluidyne (I'm not sure of the compatibility with radiator guards)
4. Which Bar Bend? Keep in mind we are targeting a 180lbs rider of average height.
5. Which Pegs??? IMS F3 Pivot, PC-Ti, White Brothers Tri-Pro Ti?
6. Final drive gearing?

Great job everyone! We are almost to the fun part...building this monster!

Ken

CRF's Only Project Bike

Bike: CRF450X
Type of Build: Offroad/Trail

Performance
JD Jetting Kit
Boyesen Quickshot
Airbox Mods
Twin Air PowerFlow Kit
??? Exhaust Yosh Carbon, E2, Others
??? CAM
Napalm Filter bolt
Zip Ty Hot Start Nut
CRF's Only Fuel Screw
Rekluse z-Start w/ Perch Adjuster
Applied Vent Kit or Rob's Vent
Applied Smog
Five-10 Case Saver
PC Thermstrips
??? Fluidyne Radiators
Zip Ty Magnetic Drain Bolt

Suspension
Forks and Shock Valved and Spings
RG3 Link

Controls
Pro Tapers
??? Bend: ???
BRP Triple Clamp
BRP SUB Mount
Scotts Stabilizer
Hammerhead Shifter
??? Pegs??? IMS F3 Pivot
PMB Kickstand
Cycra Pro-Bend CRFX Handguards Acerbis Rally Pro
Works Elite Perch
ASV Levers
ASV Perch Clamps
Spider Grips Renthal Grips
Joker Throttle

Braking
Wave Rotors
Stainless lines
Fastway Cable Clip

Wheels/Tires
Excel Rims
Talon Hubs
Dunlop 756 Tires
T.M. Designs Slide-n-glide

Protection
WC Skid Plate
WC Master Cylinder Guard
WC Rear Brake Guard
Scotts Rear Disc Protector
Flatland or Unabiker Radiator Guards
Brake Snake
Reklust Clutch Cover

Drivetrain
D.I.D 520VT Chain
??? Sprockets - Gearing?
Zip-Ty Axle Blocks

Electronics
Trail Tech Lynx and Protector or Acewell
Vortex or Tokyo Mods Ignition
Rewound stator
Baja Designs HID Headlight
Hour Meter
Rear Brake Light

Appearance
UFO White Plastics
Custom CRF's Only Graphics
Wheels: Hubs-> RED, Rims-> Silver
Hoses: Red
WC Engine Plugs
WC brake reservoir covers

Misc
IMS 3.2 G Tank - Black

[RottenRob]

4. Pro Taper Kevin Windham bend
6. 13/49
As for 1. I have the Yosh and it is a great pipe for weight savings, build and looks but I don't think it provides any HP gain, maybe the E2 would be better? Who has one and did they notice a power increase?

[Showtime]

1. E2 exhaust
2. have no clue
3. Stock is fine with me
4. Kevin Windham
5. White Brothers Ti
6. I will leave this choice up to you experts.

I was just thinking, who is providing their stock 450x for this transition???? Hmmmm, hey Ken, would it happen to be your bike were all fixin up??? ehehehe

Anyway, here's a thought. Get the sponsors on this deal to pony up the stuff so we could do a fund raising raffle for JAMES MARSHALL (Kid that broke his spine just a short time ago) when this bike is all done and after the testing by Dirt Rider. 10 bucks a ticket enters you into the drawing to win the bike. Might cut into some people's bling budget, but just an idea.

Cliff

[Roady]

I also run and like the Pro Tapers-Windham bend. Only other comment I have is the IMS tank, I definitely prefer the see through over the black having had both.

This bike will be killer!

[04 crf450]

tokyo mods ignition
ken, have you seen those fasst co flexx bars

[JoePezz]

1. Which Exhaust? White Brothers Carbon
2. Which CAM? Stock.
3. Fluidyne Radiators? Stock, so we can use Rooster Radiator guards. No one wants broken Radiators.
4. Which Bar Bend?CR Mid or Windham (Protapers)
5. Which Pegs??? White Brothers.
6. Final drive gearing? Go with whatever you feel is best.

[Ted]

1. Yosh carbon (Weight savings)
2. Stock cam (This bike will rip with the other mods and jetting)
3. Fluidyne if compatible with rad guards (if compatible use stock protection is a must)
3. I use CR High bend on my 450R
4. IMS pivot
5. Not sure of X gearing but I would want it low enough for tight rough stuff

[KaBooM]

Ken, Synergy Seals will donate a set of fork seals to the project.

Thanks, Rob

[Socal X Rider]

1. White Bros carbon (only if it has a spark arrestor - forgot if it did or not)
Yosh carbon or Pro Circuit Titanium (I know these have spark arrestors)

Final gearing is an individual taste. Is this bike going to be ridden more in the desert or tight trails or a combo of both. Go three down on the rear (48t).

Combos 13/48 or 14/49

[Ernie Pezz]

1. E2
2. Stage 2
3. Fluidyne if they fit w/rad guards
4. Keep bend height for average height rider
5. White Bros. Tri-Pro Ti
6. Gearing would depend on the terrain it was going to be tested in.

Ernie

[PGer555]

definatly the E2 exhaust...

[uniped]

Exhuast >Yosh carbon (I preffer Yoshimura)
Cam>Stage 1(low cost big gains)
Radiator>Fluidyne(again provided they are functional with guards)
Bar Bend>Woods High (Narrow for trails and bout 3/4" height increase)
Foot pegs>Fastway (not listed but adjustable)
Final drive>Suggestions should be from a 450X rider)

Thanks Ken for hold'n in there through the argumentative stage. Look forwar to some pics!

Scott
________
THINKMILL

[Smash]

1. Which Exhaust? www.mrdracing.com
2. Which CAM? Stage 2, let's give this bike some wings.
3. Fluidyne Radiators? Fluidyne looks way trick and cools well. If your ridding in socal it's nice to have.
4. Which Bar Bend? Carmichael bend, Honda can't be wrong.
5. Which Pegs??? Fastaway
6. Final drive gearing? No Opinion.

[Dust Devil]

CRF's Only Project Bike

Bike: CRF450X
Type of Build: Offroad/Trail

Performance
JD Jetting Kit
Boyesen Quickshot
Airbox Mods
Twin Air PowerFlow Kit
E2, Quiet, spark arrested, has power gain

No need for a cam

Napalm Filter bolt
Zip Ty Hot Start Nut (not that important)
CRF's Only Fuel Screw
Rekluse z-Start w/ Perch Adjuster (not needed)
Applied Vent Kit or Rob's Vent
Applied Smog (they might frown on this)
Fastway case saver Or Summers racing
PC Thermstrips (not needed)
??? Fluidyne Radiators (not needed)
Zip Ty Magnetic Drain Bolt (not needed)

Suspension
Forks and Shock Valved and Spings (precision concepts)
RG3 Link (not needed)

Controls
Pro Tapers
??? Bend: ??? (windham nice rise, very little sweep)
BRP Triple Clamp
BRP SUB Mount
Scotts Stabilizer
Hammerhead Shifter (not needed unless you have 13+ size feet)
??? Pegs??? IMS F3 Pivot (not needed)
PMB Kickstand (whats wrong with stock?)
Cycra or Enduro Engineering (I have seen where Dirt rider prefers EE)
Works Elite Perch (Why?)
ASV Levers (why?)
ASV Perch Clamps (why?)
Spider Grips
Joker Throttle (why?)

Braking (stock brakes are plenty adequate)
Wave Rotors
Stainless lines
Fastway Cable Clip

Wheels/Tires
Excel Rims
Talon Hubs

For offroad (desert) the dunlop 739F or Maxxis desert IT would be a way better choice
T.M. Designs Slide-n-glide
moose or maxxis HD tubes w/True Goo

Protection
WC Skid Plate Or Flatland
WC Master Cylinder Guard
WC Rear Brake Guard
Scotts Rear Disc Protector or EE
Flatland or Unabiker Radiator Guards (Flatland are way better)
Brake Snake
Rekluse Clutch Cover (Rekluse is not needed)

Drivetrain
D.I.D 520VT Chain
Ironman Sprockets - Gearing? 13/49 or stock
Zip-Ty Axle Blocks

Electronics
Trail Tech Lynx and Protector or Acewell
Vortex or Tokyo Mods Ignition (not needed)
Rewound stator
Baja Designs HID Headlight
Hour Meter
Rear Brake Light (not needed)

Appearance
UFO White Plastics (not needed)
Custom CRF's Only Graphics
Wheels: silver
Hoses: stock
WC Engine Plugs (lame)
WC brake reservoir covers (lame)

Misc
IMS 3.2 G Tank - Black


I suppose if you wanted to showcase every product you sell go ahead, but I dont think thats what DR is looking for.

Also might want to consider a fender bag with a front tube,Co2 kit,irons,3 way t-handle and 7 way screwdriver.

[Ted]

Also might want to consider a fender bag with a front tube,Co2 kit,irons,3 way t-handle and 7 way screwdriver.

Great idea!! I think we all overlooked that.