How to: Honda CRF Showa Fork rebuild seals and oil change
  • Smash

    How to: Honda CRF Showa Fork rebuild seals and oil change

    by Smash » Mon Jan 15, 2007 12:37 am

    Well finally, here it is. Sorry it took forever. If you have any changes or better ideas let me know and I'll add them. It's worked on my 2005 CRF450X and a friends 2003 CRF450R.

    Also, it's probably a good idea to clean your bike anytime before you work on it. As you'll notice I didn't do too good a job and the axle holder has a bunch of dirt on it. If you drop any of this in the fork it wouldn't be good. So do a better cleaning job than I did.


    CRF450R CRF450X
    Showa Fork Rebuild Procedures / Steps
    Required Parts:
    Fork Fluid - We used 5 weight from Maxima
    Pivot Works Fork Seal Kit - or you can purchase just new seals and bushings
    if required. Factory connection makes a superior Fork seal that has a more pliable
    rubber and seals a little better.

    First off measure
    how high your forks sit above the top triple clamp.
    Image

    Remove your front
    wheel and brake caliper.
    Image

    Remove your lower
    fork protectors.
    Image
    Loosen your upper
    and lower triple clamps and lower the fork down so you can
    place the fork wrench between the triple clamp and the fork. Tighten the lower
    clamp lightly to hold the fork tube while you loosen it. Once you've loosened
    the
    top cap, remove the fork.
    Image
    Mark down how many
    clicks out you have your rebound adjuster at and then turn
    counterclockwise until it stops.
    Image
    Hold the outer fork
    tube and completely loosen the fork cap.
    Image
    Slide the outer
    tube down from the fork cap.
    Image
    Remove the air bleed
    screw on the fork cap.
    Image
    Drain the forks
    completely. See your owners manual page 87 for how much
    fluid will remain after you have drained the forks.
    Image
    Hand tighten the
    cap and upper fork tube back together. Replace the air bleed screw.
    Image
    Flip the fork over,
    you'll be loosening this bolt The fork center bolt.
    Image
    We used a breaker
    bar and a crescent wrench to hold the fork foot in place.
    Image
    Once the bolt is
    loose, press down on the fork leg and the inner rod will come out of
    the fork. Place a 10mm wrench around the tube between the foot and the center
    bolt to keep it up and in place.
    Image
    Place a wrench on
    the lock nut and a socket on the fork center bolt.
    Image
    Remove the fork
    center bolt.
    Image
    Image
    Use the fork center
    bolt to remove the rod down in the fork. Slightly twise the fork
    to remove the rebound adjustment rod.
    Image
    Completely remove
    the rod.
    Image
    Here's the rod and
    adjuster.
    Image
    Remove the wrench
    and let the rod slide back into the fork leg.
    Image
    Use a screw driver
    to pry the dust seal from the upper fork tube.
    Image
    Completely slide
    up the dust seal.
    Image
    Image
    Use a screw driver
    to remove retaining ring.
    Image
    Image
    Now grab the lower
    fork leg in one hand and the upper fork leg in the other.
    Collapse the tube and pull them apart in the same fashion as a slide hammer.

    The lower fork leg will come loose (it makes a mess so be prepared).
    Place the spring back into the upper fork tube. This is what you'll now have.
    Image

    Image
    Here's the lower
    fork tube with both the bushings, the washer and the seal.
    Image
    Use a screwdriver
    to pry the upper bushing apart and remove it from the lower
    fork leg.
    Image
    Remove the lower
    bushing from the lower fork leg.
    Image
    Remove the washer
    from the lower fork leg.
    Image
    Remove the seal
    from the lower fork leg.
    Image
    Remove the retaining
    ring from the lower fork leg.
    Image
    Remove the dust
    seal from the lower fork leg.
    Image
    Clean and check
    your lower fork leg for any problems. Any deep nicks can tear
    new seals. Here's a pretty good gouge on one, but we'll run it.
    Image
    Place a sandwich
    bag over the lower fork leg.
    Image
    Grease up the sandwich
    bag so you don't tear the seals as you put them on.
    Image
    Place the dust seal
    on first. Spring facing towards the bottom of the fork.
    Image
    Place the reatining
    ring on next followed by the fork seal. With the spring facing up
    part number facing down.
    Image
    Remove the baggy
    and place the washer back on.
    Image
    Place the Lower
    bushing back into place. If your reusing your old bushing make
    sure to check the inside surface of this bearing. It's teflon coated and should
    be black
    with no silver or copper showing through it. If any of the surface isn't black
    the
    bushing should be replaced. Replace the upper fork bushing but inspecting it's
    outside surface.
    Image
    Place the lower
    fork tube back over the spring into the upper fork tube. Slide
    the lower bushing back down into the upper fork tube.
    Image
    Image
    Use the seal/bushing
    driver to press them back down into place again using a
    slide hammer motion. Not much pressure or force is needed for this.
    Image
    Image
    Make sure it's seated
    then lower down the washer into the upper fork tube.
    Image
    Press the fork seal
    back into place and use the fork/seal driver to ensure it's seated.
    Image
    Place the retaining
    ring back into place ensuring that it's seated in the grove all
    the way around.
    Image
    Place the dust seal
    back into place.
    Image
    Using your wrench
    again push down on the fork foot and push the outer rod back
    out and place the wrench underneath.
    Image
    Place the rebound
    adjustment rod back into place and ensure it's seated.
    Image
    If the rod is still
    visible its not seated. Use the fork center bolt to twist it and
    drop into place.
    Image
    The rod is properly
    seated in this photo.
    Image
    Screw the center
    fork bolt back into place. Tighten the bolt fully by hand.
    Image
    Check the clearance
    between the lock nut and the center bolt. The sepc should
    be 0.06-0.08 inches of clearance.
    Image
    Tighten the lock
    nut to the fork center bolt and torque to 16 Lbf-ft.
    Image
    Remove the wrench
    from underneath the fork center bolt and let the fork rod
    drop back into the fork. Hand tighten then torque the fork center bolt to the
    axle holder
    and torque it down to 51 Lbf-ft.
    Image
    Here's the milk
    crate I used as a fork older while working on the fork. A rag
    cushions the fork from the garage floor.
    Image
    Loosen the fork
    cap from the outer fork tube.
    Image
    Using a ratio-rate
    determine how much fluid you want in your fork. Subtract the
    amount of fluid left in your fork from the total volume you want (remember the
    chart
    above). We filled ours with 370ml of fluid as recommended in our Factory
    Connection suspenion owners manual. Stock is 338.
    Image
    Flip the fork over
    and pour the fluid into the fork.
    Image
    Tighten the outter
    fork tube and fork cap together. Only snug them with the wrench
    the triple clamps actually compress the tube enough to keep them from seperating.
    So not much force is needed.
    Image
    Let any air back
    out of the suspension from the air bleed screw.
    Image
    Reset your rebound
    adjuster back to where you had them set before.
    Image
    Replace the forks
    back in the triple clamp and make sure you have them adjusted
    as they were before. We set ours at 3MM measured from the upper triple clamp
    to the top of the upper fork tube right below the fork cap.
    Image
    Go ride. So far
    new fluid in forks has always been noticeable to me. These same
    procedures will work for the CRF450R. I'm sure it applies to most SHOWA forks
    as well.
    Last edited by Smash on Mon Jan 15, 2007 8:52 am, edited 1 time in total.
  • Eikka
    Posts: 4
    Joined: Mon Sep 25, 2006 2:52 am

    by Eikka » Mon Jan 15, 2007 2:40 am

    WOW! Great write-up! Thanks for sharing!
  • dobent4@yahoo.com
    Posts: 5039
    Joined: Sun Aug 14, 2005 6:21 pm

    by dobent4@yahoo.com » Mon Jan 15, 2007 6:05 am

    Smash,what an awesome post !
    I just printed the whole thing , I've got document protectors and am putting it in a manual with great articles in it, like this one and DD's stuff. That way I can reference info like this and have it right there in the shop.
    I get hung up on solving little stuff, because I don't think of solutions like having a hole in the side of the milk crate to make a stand. Nice job. Doug
  • User avatar
    XGiant
    Posts: 449
    Joined: Sat Apr 15, 2006 6:59 am

    by XGiant » Mon Jan 15, 2007 6:39 am

    dobent4@yahoo.com wrote:Smash,what an awesome post !
    I just printed the whole thing , I've got document protectors and am putting it in a manual with great articles in it, like this one and DD's stuff. That way I can reference info like this and have it right there in the shop.
    I get hung up on solving little stuff, because I don't think of solutions like having a hole in the side of the milk crate to make a stand. Nice job. Doug


    Brad (hkepuk) has done the same thing. He has this notebook with articles, all of the manuals that came with various aftermarket products, all of these 'How to" articles...even a custom cover (after all, he is a Graphic Artist), it is as trick as our bikes... awesome resource!

    Smash is my new hero!! GREAT post!! Hey Ken, can we get this in the "How to" section?
    Image
  • User avatar
    Old-Man
    Posts: 2718
    Joined: Fri Nov 03, 2006 9:38 pm

    by Old-Man » Mon Jan 15, 2007 8:00 am

    Nice job, I sure hope Ken keeps this where guys can find it easy.
    Old-Man

    Image
  • User avatar
    JAWS
    Posts: 4449
    Joined: Fri Jun 16, 2006 6:59 am

    by JAWS » Mon Jan 15, 2007 8:39 am

    Nice to see you have other hobbies Smash! :) Great job, very clear and able to follow.

    Joe
    Image
    '05 CRF450X,McClain suspension, Cycra Probends, Pastrana FMX Pro Tapers,BRP Sub mount & Scotts stabilizer.See carb sticky for more
  • Smash

    by Smash » Mon Jan 15, 2007 8:50 am

    JAWS wrote:Nice to see you have other hobbies Smash!


    Thanks, I have too many. If I could just learn to get rid of a few instead of picking more up all the time.
  • User avatar
    Vee5
    Posts: 634
    Joined: Fri Apr 14, 2006 8:35 am

    by Vee5 » Mon Jan 15, 2007 10:23 am

    Thanks Smash- Excellent info that I will definitely use when the time comes. Thanks for your efforts!
    Is it beer :30 yet?
    Image
  • User avatar
    nowazzu
    Posts: 775
    Joined: Wed Jun 29, 2005 12:02 pm

    by nowazzu » Mon Jan 15, 2007 1:52 pm

    Looks good man. A couple of comments for others to think about. First, a bench vise with a fork holding tool makes the job even easier. Second, once you disassemble to forks, be sure to thoroughly clean the components with a parts cleaner. And finally, I noticed you only focused on the outer tube oil and the seals. Since you have it torn apart already, you may want to go ahead and open the inner chamber and change that oil too. That stuff get's worked hard since it does all the dampening.

    Again, looks good. I need to send my stuff to you now for service...
    -nowazzu-
    05' CRF450X
  • Smash

    by Smash » Mon Jan 15, 2007 2:06 pm

    nowazzu wrote:Looks good man. A couple of comments for others to think about. First, a bench vise with a fork holding tool makes the job even easier. Second, once you disassemble to forks, be sure to thoroughly clean the components with a parts cleaner. And finally, I noticed you only focused on the outer tube oil and the seals. Since you have it torn apart already, you may want to go ahead and open the inner chamber and change that oil too. That stuff get's worked hard since it does all the dampening.

    Again, looks good. I need to send my stuff to you now for service...


    Yup I agree, but have you seen my benches, there's no way I could work on those things!!! Too much junk.

    I'll have to work that inner chamber into a part 2.

    Hey how about that shock how to? I'm going through the bike and will need to redo mine before adelanto.
  • User avatar
    nowazzu
    Posts: 775
    Joined: Wed Jun 29, 2005 12:02 pm

    by nowazzu » Mon Jan 15, 2007 2:41 pm

    Smash wrote:
    nowazzu wrote:Looks good man. A couple of comments for others to think about. First, a bench vise with a fork holding tool makes the job even easier. Second, once you disassemble to forks, be sure to thoroughly clean the components with a parts cleaner. And finally, I noticed you only focused on the outer tube oil and the seals. Since you have it torn apart already, you may want to go ahead and open the inner chamber and change that oil too. That stuff get's worked hard since it does all the dampening.

    Again, looks good. I need to send my stuff to you now for service...


    Yup I agree, but have you seen my benches, there's no way I could work on those things!!! Too much junk.

    I'll have to work that inner chamber into a part 2.

    Hey how about that shock how to? I'm going through the bike and will need to redo mine before adelanto.


    Hey, it took you 6 months to write up the forks, give me a break! Actually, I need to change the seals and oil on my shock, so maybe I'll do it and write it up. Now I just need to get over this damn stomach bug.
    -nowazzu-
    05' CRF450X
  • Smash

    by Smash » Mon Jan 15, 2007 2:44 pm

    nowazzu wrote:
    Hey, it took you 6 months to write up the forks, give me a break! Actually, I need to change the seals and oil on my shock, so maybe I'll do it and write it up. Now I just need to get over this damn stomach bug.


    LOL, yup I finally get something done and get pushy!

    Good luck on the stomach bug. I got something weird on Friday and was out for 2 days. The one I had in December lasted forever.
  • User avatar
    Killaz
    Posts: 199
    Joined: Thu Jan 05, 2006 10:55 pm

    by Killaz » Mon Jan 15, 2007 4:04 pm

    Wow great post.

    How long does this procedure take?
    '05 CRF450X
    '03 YZ250
  • Smash

    by Smash » Mon Jan 15, 2007 4:10 pm

    Killaz wrote:Wow great post.

    How long does this procedure take?


    The first time about an hour or so per fork. Just making sure I did everything right. I've done it about 3 times now and can do the whole job in just over an hour (including removing them from the bike). That's probably still a little slower than the pros, but I tend to double check stuff and then doubt myself and check again.
  • User avatar
    ~R.Dawg
    Posts: 43
    Joined: Sun Apr 09, 2006 8:00 pm

    by ~R.Dawg » Mon Jan 15, 2007 7:39 pm

    I was just about to do this. This is a great write up. You would never see this on TT. Need to put this in the how to section. Good job Smash \:D/
    When in doubt, hit the gas!!

Who is online

Users browsing this forum: No registered users and 2 guests